A trained operator was blending water, sand, anhydrite, lime, cement, pulverized fly ash, and powdered aluminum in a mixing chamber to produce material for making concrete building blocks. In the blending process, sand and water are mixed to form a slurry, and then the powders are dispensed automatically into the mix by a computer-controlled system. Finally, a slurry of glycol-coated aluminum powder is added in the last few seconds before the mix is discharged into a car, and then molds are filled from the car. Adding aluminum to the mixture results in a small amount of hydrogen gas evolution, which disperses from the car into the surrounding ventilated area and out through roof vents. In addition to being an ingredient of the mix, water also helps to keep the mixture cool.

view more

First responders were dispatched to the waterfront area to investigate a possible explosion on an 85-foot dinner cruise boat that was moored there. Upon arrival, the incident commander noted that nothing out of the ordinary was visible on the exterior of the boat. A crew was sent to the interior of the boat to investigate. The boat was powered by diesel engines and there were no compressed gas cylinders on board.

After further investigation, it became apparent that the explosion had come from the battery compartment in the hull of the boat. The responders concluded that one of the batteries had been giving off hydrogen gas, which gradually built up inside the compartment. Since the compartment was not vented, the gas had nowhere to go. It found an ignition source (possibly a view more

Overview: A hydrogen leak and explosion occurred due to the installation of an incorrectly sized gasket at the suction line of a hydrogen compressor in a refinery hydrodesulfurization plant. The incorrectly sized gasket was mounted during the startup of the plant in 2001 and had never being inspected nor replaced.

Incident synopsis: The operating conditions were stable when the operator received an alarm indicating pressure loss in the circuit. He immediately instructed his field personnel to inspect the area. The hydrogen leak was confined inside the compressor room because the walls and roof were not provided with ventilation devices. An explosion occurred, causing two fatalities and the destruction of the compressor room and some of the surrounding area.

An accident occurred during setup for a popular hydrogen-oxygen balloon science demonstration at a local public school. The demonstrator suffered painful second-degree burns to his right forearm and was taken to the hospital. The paramedics feared that grave respiratory damage (due to flame inhalation) might have occurred.

The demonstrator had transported 15 helium-quality balloons, pre-filled with a hydrogen-oxygen mixture, in a large, black, polyethylene garbage bag. During the setup, he opened the bag to remove a single balloon for stringing and floating. Without warning, the entire bag of balloons detonated violently. Fortunately, the incident occurred an hour prior to the program and no one else was near. It was also fortunate that only a small box caught fire and none of view more

During the early morning hours on a Tuesday, a university support staff member was preparing for an off-campus community outreach program for high-school-age students in the community. One of the program demonstrations was to show students the reaction energy and properties of the hydrogen + oxygen = water chemical reaction. It was a demonstration that the professor and the staff member overseeing the program had done for over 15 years with no incidents ever occurring.

To prepare for the demonstration, eight balloons were filled, four with pure hydrogen and four with the proper combination of hydrogen and oxygen. The balloons were placed into a larger plastic garbage bag and carried outside to a university-owned SUV located next to the building's loading dock. The bag of view more

A fatal accident took place at an onshore processing facility for slop water from the offshore petroleum industry.

Drilling fluids, or mud, are typically oil-water emulsions consisting of base oil (continuous phase), water (dispersed phase), and emulsifying agents. Used drilling mud, or slop, is mud enriched with water and rock cuttings from drilling --- typically 60-80% water, 10-20% emulated base oil, and 10-20% rock cuttings. The used drilling fluids are collected in slop tanks on oil platforms and later shipped to onshore facilities for further processing.

On the day of the accident, two operators were trying to remove the lid from a manhole on top of a 1600-cubic meter storage tank. However, they were not able to unscrew the rusted bolts holding the lid in place, and view more